Digitrax Hints/Digitrax Audible Alerts
DCCWiki, a community DCC encyclopedia.
| Digitrax Command Station Audible Alerts | |
|---|---|
| DCCWiki.com | |
| DCS100/DCS200 Messages | |
| 1 | DCS100/200/DB150 has powered on successfully or has sent a programming command. |
| 3 | A locomotive address has been purged/dispatched due to inactivity. This is informational only and is normal. |
| 4 | Booster short circuit shutdown. Fault Alarm. |
| 6 | Command station already present in system. When two command stations are operating on the same system, you may experience unexpected results. |
| 7 | DCS100/200 internal battery low condition. Battery should be replaced as soon as possible. See your manual for instructions. |
| 8 | Memory ECC/Checksum fail. Indicates that the local memory has been corrupted and was reset automatically. This is a technical diagnostic. |
| 9 | DCS100/200 transmit failure, there is a device blocking proper message action on LocoNet. |
| 16 | Software timeout failure. No action is required, the unit will resume operation. |
| DB150 Messages | |
| 1 | successful power up or a command has been transmitted. |
| 3 | A locomotive address has been purged/dispatched due to inactivity. |
| 5 | DB150: Short circuit, booster section has shut down. |
| 6 | Conflict, the DB150 is in command station mode after powering up, and there is another command station already active on the LocoNet. Only one command station should be active at any time. |
| 9 | A transmit failure has occurred, something on the LocoNet is blocking communications. |
| 16 | Software failure occurred due to a timeout. No action required, the DB150 will clear up the problem and operation will continue as normal. |
| Random (diagnostic) clicks indicate that OpSw 41 is closed, telling the DB150 to click whenever a valid LocoNet command is received. | |
| DCS210/DCS210+ | |
| Short Beep | |
| 1 | Diagnostic Beep when OpSw41 = c, LocoNet commands incoming. In EZ Routes mode, indicates a switch has been saved. During operation, DCS210/DCS210+ has recovered from a fault |
| 2 | Initial DCS210 Power on or DCS210 had purged a loco address |
| 3 | Entered quick routes mode |
| 4 | Booster short circuit shutdown |
| 5 | Route Error, looping route |
| 8 | Route Error, Maximum switch commands issued |
| Long Beep | |
| 1 | In EZ Routes, initial Route ID saved |
| 2 | In EZ Routes, route saved and exit EZ Routes |
| 3 | When pressing the Loco Reset Button, all loco addresses purged from the system |
| 4 | Input Voltage out of the range 13.8V to 24V DC |
| 10 | DCS210 has detected another Command Station on LocoNet and has turned off track power |
| DCS240 Messages | |
| Short Beep | |
| 1 | Diagnostic Beep when OPSW41='c', LocoNet commands incoming. In EZ Routes mode, indicates a switch has been saved. During operation, the DCS240 has recovered from a fault |
| 2 | Initial DCS240 Power on or DCS240 had a purged loco address |
| 3 | Entered quick routes mode |
| 4 | Booster short circuit shutdown |
| 5 | Route Error, looping route |
| 8 | Route Error, maximum number of switch commands issued. |
| Long Beep | |
| 1 | In EZ Routes, initial Route ID saved |
| 2 | In EZ Routes, route saved and exit EZ Routes |
| 3 | When pressing the LocoReset Button, all loco addresses purged from the system. LocoPurged from system |
| 4 | Power Supply Voltage Out of Range (13.8V to 24 V DC) |
| 10 | There is another command station on the system. The DCS240 will beep ten times and cut track power. The DCS240 actively scans the LocoNet looking for command stations every two minutes, and if it finds one, will beep and cut track power. Track power cannot be restored until the offending command station is disconnected from LocoNet or switched back to Booster Mode. This feature is useful on large modular layouts. |